We have extensive applications for developed for cannabis applications, but if you have an open style greenhouses (you mentioned a canopy) these applications will need some adjustments.
The best approach is comprehensive, meaning the use of ClO2 through out the grow, at every stage of the operation.
Facility Sanitization:
– For Use in Foot Baths: Add 2 tablets to 5 gallons of water for a concentration of 10 PPM.
– Non-Porous Surfaces Such as Floors, Walls, and Ceilings: For general surfaces prepare spray at 10 PPM. Allow the mixture to air dry, no need to wipe down surfaces.
– To Sanitize Fans, HVAC, and Air Exchangers: When gassing an area, cycle fans, HVAC and air exchangers.
– Use to Clean Employee Break Rooms/Restrooms: 10 PPM as a replacement for bleach or isopropyl alcohol. Spray and let air dry.
– Odor Removal for Clothing, Employee Automobiles, or Wherever Cannabis Odors Linger Outside of the Grow: Gas at 20 tablets to 2 oz of water for 6 to 24 hours in an enclosed area. Allow for 30 minutes or longer for air-out after treatment, depending on ventilation/air flow.
– Carbon and RO Filters: Pre-clean at 3 PPM. Anything over 40 PPM with reduce the effectiveness of the filter.
– Clean Mini-Splits: Mix 1 tablet in 32 Oz spray bottle for a 100 PPM solution. Turn Fan down to low and spray directly where buildup is present.
Treatment for Irrigation, Water Tanks & Reservoirs:
– Incoming Water Lines: Treat with ClO2 injection at 1 PPM.
– Injection Systems: Run with nutrients up to 1 PPM.
– Water Tanks: Treat at 1 PPM, which will keep feed reservoirs clean and free of mold, slime and algae. Slowly add tablets directly to reservoir AFTER mixing in nutrients (mixing before will pre-release the ClO2 from the water). Add fresh tabs every other day
– Irrigation Lines: Flush between grow cycles at 50-100 PPM to eliminate biofilm build up without causing micro abrasions to the inner diameter of the lines.
Grow Room Reset (No Plants Present):
– Beginning at the top and working downwards, spray the ceiling, light fixtures, walls, tables and the floor at 10 PPM and allow to air dry.
– Flush all irrigation lines and clean drains, especially open or french style drains, at 50 PPM.
– Use Safrax® to gas the grow areas at 1 tablet per 100 ft³, using 2 oz of water per 10 tablets. ADD TABLETS SLOWLY. Treat for a minimum of 6 hours to 24 hours.
Treatment During Growth Phases:
– Dipping Cuttings to Prevent Disease: Submerge cutting in a 5 PPM solution allowing moisture to naturally air dry.
– Sanitizing Coco Clone Cubes and Coco Pre-Filled Bags: Treat at 5 PPM for 10 MINUTES for coco cubes. When blowing up coco pre-filled bags, treat at 5 PPM, then please allow 24 hours before planting clones into bags.
Integrated Pest Management:
– Spray at 5 PPM directly on plants, from substrate to the top of the plant, covering all areas. Turn off lights. You do not have to turn off dehumidifiers or HVAC.
– “5 PPM a day keeps problems away.”
Powdery Mildew:
– If Powdery Mildew is Present: Use at a concentration of 50 PPM (2 tablets/gallon of water), spray directly on the entire plant.
Harvest Protocols:
– Sanitize all tools at 500 PPM (20 tablets/gallon), let sit 1 minute, then rinse.
– Sanitize all surfaces including tables, harvest equipment, tops of pots, and another other contact surfaces where flower may touch. Spray at 100 PPM (4 tablets/gallon) and allow to air dry, no need to wipe down.
Use in Dry Room with Drying Cannabis to Purify Air:
– First 24 Hours: 200 tablets in 2 cups of water in a 5 gallon bucket treats 2500 ft³. ADD TABLETS SLOWLY.
– Second 24 Hours: 200 tablets in 2 cups of water per 2500 ft³.
– Third and Final Day: 100 tablets in 1 cup of water.
– After Third Day: Finish drying normally.
Wet Trim Method:
– Use fine mist such as an atomizer or fine spray nozzle on finished buds for added yeast and mold protection. Mist entire bud at 50 PPM.
To treat a canopy, the gas method (no plant present) would be best recommended. if there are plants present, and if you have an open-style greenhouse, we would recommend applying a ClO2 solution with an electrostatic fogger at 50 PPM.
Please email me at taeghan@safrax.com if you wish access to our full Cannabis Applications brochure and if you would like to discuss your application requirements in greater detail.
Hi there,
We have extensive applications for developed for cannabis applications, but if you have an open style greenhouses (you mentioned a canopy) these applications will need some adjustments.
The best approach is comprehensive, meaning the use of ClO2 through out the grow, at every stage of the operation.
Facility Sanitization:
– For Use in Foot Baths: Add 2 tablets to 5 gallons of water for a concentration of 10 PPM.
– Non-Porous Surfaces Such as Floors, Walls, and Ceilings: For general surfaces prepare spray at 10 PPM. Allow the mixture to air dry, no need to wipe down surfaces.
– To Sanitize Fans, HVAC, and Air Exchangers: When gassing an area, cycle fans, HVAC and air exchangers.
– Use to Clean Employee Break Rooms/Restrooms: 10 PPM as a replacement for bleach or isopropyl alcohol. Spray and let air dry.
– Odor Removal for Clothing, Employee Automobiles, or Wherever Cannabis Odors Linger Outside of the Grow: Gas at 20 tablets to 2 oz of water for 6 to 24 hours in an enclosed area. Allow for 30 minutes or longer for air-out after treatment, depending on ventilation/air flow.
– Carbon and RO Filters: Pre-clean at 3 PPM. Anything over 40 PPM with reduce the effectiveness of the filter.
– Clean Mini-Splits: Mix 1 tablet in 32 Oz spray bottle for a 100 PPM solution. Turn Fan down to low and spray directly where buildup is present.
Treatment for Irrigation, Water Tanks & Reservoirs:
– Incoming Water Lines: Treat with ClO2 injection at 1 PPM.
– Injection Systems: Run with nutrients up to 1 PPM.
– Water Tanks: Treat at 1 PPM, which will keep feed reservoirs clean and free of mold, slime and algae. Slowly add tablets directly to reservoir AFTER mixing in nutrients (mixing before will pre-release the ClO2 from the water). Add fresh tabs every other day
– Irrigation Lines: Flush between grow cycles at 50-100 PPM to eliminate biofilm build up without causing micro abrasions to the inner diameter of the lines.
Grow Room Reset (No Plants Present):
– Beginning at the top and working downwards, spray the ceiling, light fixtures, walls, tables and the floor at 10 PPM and allow to air dry.
– Flush all irrigation lines and clean drains, especially open or french style drains, at 50 PPM.
– Use Safrax® to gas the grow areas at 1 tablet per 100 ft³, using 2 oz of water per 10 tablets. ADD TABLETS SLOWLY. Treat for a minimum of 6 hours to 24 hours.
Treatment During Growth Phases:
– Dipping Cuttings to Prevent Disease: Submerge cutting in a 5 PPM solution allowing moisture to naturally air dry.
– Sanitizing Coco Clone Cubes and Coco Pre-Filled Bags: Treat at 5 PPM for 10 MINUTES for coco cubes. When blowing up coco pre-filled bags, treat at 5 PPM, then please allow 24 hours before planting clones into bags.
Integrated Pest Management:
– Spray at 5 PPM directly on plants, from substrate to the top of the plant, covering all areas. Turn off lights. You do not have to turn off dehumidifiers or HVAC.
– “5 PPM a day keeps problems away.”
Powdery Mildew:
– If Powdery Mildew is Present: Use at a concentration of 50 PPM (2 tablets/gallon of water), spray directly on the entire plant.
Harvest Protocols:
– Sanitize all tools at 500 PPM (20 tablets/gallon), let sit 1 minute, then rinse.
– Sanitize all surfaces including tables, harvest equipment, tops of pots, and another other contact surfaces where flower may touch. Spray at 100 PPM (4 tablets/gallon) and allow to air dry, no need to wipe down.
Use in Dry Room with Drying Cannabis to Purify Air:
– First 24 Hours: 200 tablets in 2 cups of water in a 5 gallon bucket treats 2500 ft³. ADD TABLETS SLOWLY.
– Second 24 Hours: 200 tablets in 2 cups of water per 2500 ft³.
– Third and Final Day: 100 tablets in 1 cup of water.
– After Third Day: Finish drying normally.
Wet Trim Method:
– Use fine mist such as an atomizer or fine spray nozzle on finished buds for added yeast and mold protection. Mist entire bud at 50 PPM.
To treat a canopy, the gas method (no plant present) would be best recommended. if there are plants present, and if you have an open-style greenhouse, we would recommend applying a ClO2 solution with an electrostatic fogger at 50 PPM.
Please email me at taeghan@safrax.com if you wish access to our full Cannabis Applications brochure and if you would like to discuss your application requirements in greater detail.
Warm regards,
KT
Safrax.com